BootROM - 1.73
Booting from NAND flash

General initialization - Version: 1.0.0
AVS selection from EFUSE disabled (Skip reading EFUSE values)
mvSysEnvIsFlavourReduced: TWSI Read of 'flavor' failed
Detected Device ID 6820
High speed PHY - Version: 2.0

Init RD NAS topology Serdes Lane 3 is USB3
Serdes Lane 4 is SGMII
board SerDes lanes topology details:
 | Lane # | Speed|    Type     |
 ------------------------------|
 |   0    |  6   |  SATA0      |
 |   1    |  5   |  PCIe0      |
 |   2    |  6   |  SATA1      |
 |   3    |  5   |  USB3 HOST1 |
 |   4    |  5   |  PCIe1      |
 |   5    |  0   |  SGMII2     |
 -------------------------------
:** Link is Gen1, check the EP capability
PCIe, Idx 0: Link upgraded to Gen2 based on client cpabilities
:** Link is Gen1, check the EP capability
PCIe, Idx 1: remains Gen1
High speed PHY - Ended Successfully
DDR3 Training Sequence - Ver TIP-1.46.0
mvSysEnvGetTopologyUpdateInfo: TWSI Read failed
DDR3 Training Sequence - Switching XBAR Window to FastPath Window
DDR3 Training Sequence - Ended Successfully
Not detected suspend to RAM indication
BootROM: Image checksum verification PASSED


U-Boot 2013.01 (Sep 25 2017 - 11:42:52) Marvell version: 2015_T1.QA.0p16

Boot version : v1.0.0

Board: RD-NAS-88F6820-DDR3
SoC:   MV88F6820 Rev A0
       running 2 CPUs
CPU:   ARM Cortex A9 MPCore (Rev 1) LE
       CPU 0
       CPU    @ 1866 [MHz]
       L2     @ 933 [MHz]
       TClock @ 200 [MHz]
       DDR3    @ 933 [MHz]
       DDR3 32 Bit Width,FastPath Memory Access, DLB Enabled, ECC Disabled
DRAM:  512 MiB
NAND:  256 MiB
MMC:   mv_sdh: 0


#### auto_recovery ####
[u_env] get auto_recovery == yes
[u_env] get auto_recovery == yes
[u_env] get boot_part == 1
[u_env] get boot_part_ready == 3
auto_recovery enabled:1, boot_part:1, boot_part_ready:3

[boot_count_read] block:0x220000, size:128KB, records:64
[boot_count_read_record] boot_count:2, next_record:2

[boot_count_write] erase:0, auto_recovery->block_offset:0x220000 offset=0x221000

Updating boot_count ...
[boot_count_write] offset:0x221000 , length:2048
done

PCI-e 0 (IF 0 - bus 0) Root Complex Interface, Detected Link X1, GEN 2.0
PCI-e 1 (IF 1 - bus 1) Root Complex Interface, Detected Link X1, GEN 1.1
USB2.0 0: Host Mode
USB3.0 1: Host Mode
USB3.0 0: Host Mode

Map:   Code:                    0x1feab000:0x1ff75c30
       BSS:                     0x1ffef564
       Stack:                   0x1f9aaf20
       Heap:                    0x1f9ab000:0x1feab000
       U-Boot Environment:      0x00200000:0x00220000 (NAND)

Board configuration detected:
mvEthE6171SwitchBasicInit init
Net:
|  port  | Interface | PHY address  |
|--------|-----------|--------------|
| egiga0 |   RGMII   |     0x01     |
| egiga1 |   SGMII   |     0x00     |
| egiga2 |   SGMII   |   In-Band    |
egiga0 [PRIME], egiga1, egiga2
auto_recovery_check changes bootcmd: run nandboot
Hit any key to stop autoboot:  0

NAND read: device 0 offset 0xa00000, size 0x600000
 6291456 bytes read: OK
## Booting kernel from Legacy Image at 02000000 ...
   Image Name:   ARM OpenWrt Linux-5.15.92
   Created:      2023-02-07  23:51:12 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    3595003 Bytes = 3.4 MiB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK

Starting kernel ...