BootROM - 1.73 Booting from NAND flash General initialization - Version: 1.0.0 AVS selection from EFUSE disabled (Skip reading EFUSE values) mvSysEnvIsFlavourReduced: TWSI Read of 'flavor' failed Detected Device ID 6820 High speed PHY - Version: 2.0 Init RD NAS topology Serdes Lane 3 is USB3 Serdes Lane 4 is SGMII board SerDes lanes topology details: | Lane # | Speed| Type | ------------------------------| | 0 | 6 | SATA0 | | 1 | 5 | PCIe0 | | 2 | 6 | SATA1 | | 3 | 5 | USB3 HOST1 | | 4 | 5 | PCIe1 | | 5 | 0 | SGMII2 | ------------------------------- :** Link is Gen1, check the EP capability PCIe, Idx 0: Link upgraded to Gen2 based on client cpabilities :** Link is Gen1, check the EP capability PCIe, Idx 1: remains Gen1 High speed PHY - Ended Successfully DDR3 Training Sequence - Ver TIP-1.46.0 mvSysEnvGetTopologyUpdateInfo: TWSI Read failed DDR3 Training Sequence - Switching XBAR Window to FastPath Window DDR3 Training Sequence - Ended Successfully Not detected suspend to RAM indication BootROM: Image checksum verification PASSED U-Boot 2013.01 (Sep 25 2017 - 11:42:52) Marvell version: 2015_T1.QA.0p16 Boot version : v1.0.0 Board: RD-NAS-88F6820-DDR3 SoC: MV88F6820 Rev A0 running 2 CPUs CPU: ARM Cortex A9 MPCore (Rev 1) LE CPU 0 CPU @ 1866 [MHz] L2 @ 933 [MHz] TClock @ 200 [MHz] DDR3 @ 933 [MHz] DDR3 32 Bit Width,FastPath Memory Access, DLB Enabled, ECC Disabled DRAM: 512 MiB NAND: 256 MiB MMC: mv_sdh: 0 #### auto_recovery #### [u_env] get auto_recovery == yes [u_env] get auto_recovery == yes [u_env] get boot_part == 1 [u_env] get boot_part_ready == 3 auto_recovery enabled:1, boot_part:1, boot_part_ready:3 [boot_count_read] block:0x220000, size:128KB, records:64 [boot_count_read_record] boot_count:0, next_record:32 [boot_count_write] erase:0, auto_recovery->block_offset:0x220000 offset=0x230000 Updating boot_count ... [boot_count_write] offset:0x230000 , length:2048 done PCI-e 0 (IF 0 - bus 0) Root Complex Interface, Detected Link X1, GEN 2.0 PCI-e 1 (IF 1 - bus 1) Root Complex Interface, Detected Link X1, GEN 1.1 USB2.0 0: Host Mode USB3.0 1: Host Mode USB3.0 0: Host Mode Map: Code: 0x1feab000:0x1ff75c30 BSS: 0x1ffef564 Stack: 0x1f9aaf20 Heap: 0x1f9ab000:0x1feab000 U-Boot Environment: 0x00200000:0x00220000 (NAND) Board configuration detected: mvEthE6171SwitchBasicInit init Net: | port | Interface | PHY address | |--------|-----------|--------------| | egiga0 | RGMII | 0x01 | | egiga1 | SGMII | 0x00 | | egiga2 | SGMII | In-Band | egiga0 [PRIME], egiga1, egiga2 auto_recovery_check changes bootcmd: run nandboot Hit any key to stop autoboot: 0 NAND read: device 0 offset 0xa00000, size 0x600000 6291456 bytes read: OK ## Booting kernel from Legacy Image at 02000000 ... Image Name: ARM OpenWrt Linux-5.15.92 Created: 2023-02-07 23:51:12 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3596635 Bytes = 3.4 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.15.92 (g@gMac.local) (arm-openwrt-linux-muslgnueabi-gcc (OpenWrt GCC 12.2.0 r22010-89fcd1c6bd) 12.2.0, GNU ld (GNU Binutils) 2.39) #0 SMP Tue Feb 7 23:51:12 2023 [ 0.000000] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Linksys WRT3200ACM [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x000000001fffffff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x000000001fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000001fffffff] [ 0.000000] percpu: Embedded 11 pages/cpu s14028 r8192 d22836 u45056 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129920 [ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/mtdblock6 ro rootdelay=1 rootfstype=jffs2 earlyprintk mtdparts=armada-nand:2048K(uboot)ro,128K(u_env),256K(s_env),256K@8064K(devinfo),1920K@8320K(sysdiag),80m@10m(kernel),74m@16m(rootfs),80m@90m(alt_kernel),74m@96m(alt_rootfs),160m@10m(ubifs),-@170m(syscfg) [ 0.000000] Bootloader command line (ignored): console=ttyS0,115200 root=/dev/mtdblock6 ro rootdelay=1 rootfstype=jffs2 earlyprintk mtdparts=armada-nand:2048K(uboot)ro,128K(u_env),256K(s_env),256K@8064K(devinfo),1920K@8320K(sysdiag),80m@10m(kernel),74m@16m(rootfs),80m@90m(alt_kernel),74m@96m(alt_rootfs),160m@10m(ubifs),-@170m(syscfg) [ 0.000000] Unknown kernel command line parameters "earlyprintk mangled_fs=jffs2 mtdparts=armada-nand:2048K(uboot)ro,128K(u_env),256K(s_env),256K@8064K(devinfo),1920K@8320K(sysdiag),80m@10m(kernel),74m@16m(rootfs),80m@90m(alt_kernel),74m@96m(alt_rootfs),160m@10m(ubifs),-@170m(syscfg)", will be passed to user space. [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 505924K/524288K available (8192K kernel code, 636K rwdata, 1896K rodata, 1024K init, 235K bss, 18364K reserved, 0K cma-reserved, 0K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] L2C: DT/platform modifies aux control register: 0x06070000 -> 0x16070000 [ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 [ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 [ 0.000000] L2C-310 D prefetch enabled, offset 1 lines [ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled [ 0.000000] L2C-310 Coherent cache controller enabled, 16 ways, 1024 kB [ 0.000000] L2C-310 Coherent: CACHE_ID 0x410054c9, AUX_CTRL 0x56070001 [ 0.000000] sched_clock: 64 bits at 933MHz, resolution 1ns, wraps every 4398046511103ns [ 0.000014] clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x1ae5b571769, max_idle_ns: 881590513431 ns [ 0.000028] Switching to timer-based delay loop, resolution 1ns [ 0.000133] Ignoring duplicate/late registration of read_current_timer delay [ 0.000138] clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 76450417870 ns [ 0.000272] Calibrating delay loop (skipped), value calculated using timer frequency.. 1866.00 BogoMIPS (lpj=9330000) [ 0.000280] pid_max: default: 32768 minimum: 301 [ 0.000355] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.000363] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.000674] CPU: Testing write buffer coherency: ok [ 0.000690] CPU0: Spectre v2: using BPIALL workaround [ 0.000773] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.001021] Setting up static identity map for 0x100000 - 0x100060 [ 0.001085] mvebu-soc-id: MVEBU SoC ID=0x6820, Rev=0x4 [ 0.001150] mvebu-pmsu: Initializing Power Management Service Unit [ 0.001201] rcu: Hierarchical SRCU implementation. [ 0.001267] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build [ 0.001318] smp: Bringing up secondary CPUs ... [ 0.001454] Booting CPU 1 [ 0.001570] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.001575] CPU1: Spectre v2: using BPIALL workaround [ 0.001619] smp: Brought up 1 node, 2 CPUs [ 0.001624] SMP: Total of 2 processors activated (3732.00 BogoMIPS). [ 0.001629] CPU: All CPU(s) started in SVC mode. [ 0.003126] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 0.003169] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.003177] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.003236] pinctrl core: initialized pinctrl subsystem [ 0.003664] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.004120] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.004453] thermal_sys: Registered thermal governor 'step_wise' [ 0.004562] cpuidle: using governor ladder [ 0.004692] mvebu-pmsu: CPU hotplug support is currently broken on Armada 38x: disabling [ 0.004698] mvebu-pmsu: CPU idle is currently broken on Armada 38x: disabling [ 0.010761] cryptd: max_cpu_qlen set to 1000 [ 0.011568] SCSI subsystem initialized [ 0.011707] usbcore: registered new interface driver usbfs [ 0.011724] usbcore: registered new interface driver hub [ 0.011740] usbcore: registered new device driver usb [ 0.012272] clocksource: Switched to clocksource arm_global_timer [ 0.012542] NET: Registered PF_INET protocol family [ 0.012617] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.012889] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 0.012905] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.012912] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 0.012932] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.012962] TCP: Hash tables configured (established 4096 bind 4096) [ 0.012994] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.013010] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.013094] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.013110] PCI: CLS 0 bytes, default 64 [ 0.014221] workingset: timestamp_bits=14 max_order=17 bucket_order=3 [ 0.015827] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.015834] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.017082] armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver [ 0.017520] debugfs: Directory 'f1018100.gpio' with parent 'regmap' already present! [ 0.017728] debugfs: Directory 'f1018140.gpio' with parent 'regmap' already present! [ 0.017946] mvebu-pcie soc:pcie: host bridge /soc/pcie ranges: [ 0.017968] mvebu-pcie soc:pcie: MEM 0x00f1080000..0x00f1081fff -> 0x0000080000 [ 0.017981] mvebu-pcie soc:pcie: MEM 0x00f1040000..0x00f1041fff -> 0x0000040000 [ 0.017992] mvebu-pcie soc:pcie: MEM 0x00f1044000..0x00f1045fff -> 0x0000044000 [ 0.018004] mvebu-pcie soc:pcie: MEM 0x00f1048000..0x00f1049fff -> 0x0000048000 [ 0.018015] mvebu-pcie soc:pcie: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0100000000 [ 0.018025] mvebu-pcie soc:pcie: IO 0xffffffffffffffff..0x00fffffffe -> 0x0100000000 [ 0.018035] mvebu-pcie soc:pcie: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0200000000 [ 0.018044] mvebu-pcie soc:pcie: IO 0xffffffffffffffff..0x00fffffffe -> 0x0200000000 [ 0.018054] mvebu-pcie soc:pcie: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0300000000 [ 0.018064] mvebu-pcie soc:pcie: IO 0xffffffffffffffff..0x00fffffffe -> 0x0300000000 [ 0.018073] mvebu-pcie soc:pcie: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0400000000 [ 0.018080] mvebu-pcie soc:pcie: IO 0xffffffffffffffff..0x00fffffffe -> 0x0400000000 [ 0.018181] mvebu-pcie soc:pcie: PCI host bridge to bus 0000:00 [ 0.018189] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.018196] pci_bus 0000:00: root bus resource [mem 0xf1080000-0xf1081fff] (bus address [0x00080000-0x00081fff]) [ 0.018202] pci_bus 0000:00: root bus resource [mem 0xf1040000-0xf1041fff] (bus address [0x00040000-0x00041fff]) [ 0.018208] pci_bus 0000:00: root bus resource [mem 0xf1044000-0xf1045fff] (bus address [0x00044000-0x00045fff]) [ 0.018213] pci_bus 0000:00: root bus resource [mem 0xf1048000-0xf1049fff] (bus address [0x00048000-0x00049fff]) [ 0.018218] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff] [ 0.018223] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff] [ 0.018287] pci 0000:00:01.0: [11ab:6820] type 01 class 0x060400 [ 0.018420] pci 0000:00:02.0: [11ab:6820] type 01 class 0x060400 [ 0.019109] PCI: bus0: Fast back to back transfers disabled [ 0.019115] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 0.019123] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 0.019182] pci 0000:01:00.0: [11ab:2b40] type 00 class 0x020000 [ 0.019199] pci 0000:01:00.0: reg 0x10: [mem 0x40000000-0x401fffff 64bit pref] [ 0.019212] pci 0000:01:00.0: reg 0x18: [mem 0x40200000-0x402fffff 64bit pref] [ 0.019277] pci 0000:01:00.0: supports D1 D2 [ 0.019281] pci 0000:01:00.0: PME# supported from D0 D1 D3hot D3cold [ 0.019999] PCI: bus1: Fast back to back transfers disabled [ 0.020005] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 0.020101] pci 0000:02:00.0: [11ab:2b40] type 00 class 0x020000 [ 0.020122] pci 0000:02:00.0: reg 0x10: [mem 0x42000000-0x421fffff 64bit pref] [ 0.020137] pci 0000:02:00.0: reg 0x18: [mem 0x42200000-0x422fffff 64bit pref] [ 0.020226] pci 0000:02:00.0: supports D1 D2 [ 0.020231] pci 0000:02:00.0: PME# supported from D0 D1 D3hot D3cold [ 0.020255] pci 0000:02:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:02.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link) [ 0.020966] PCI: bus2: Fast back to back transfers disabled [ 0.020971] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02 [ 0.020997] pci 0000:00:01.0: BAR 8: assigned [mem 0xe0000000-0xe02fffff] [ 0.021005] pci 0000:00:02.0: BAR 8: assigned [mem 0xe0400000-0xe06fffff] [ 0.021012] pci 0000:01:00.0: BAR 0: assigned [mem 0xe0000000-0xe01fffff 64bit pref] [ 0.021022] pci 0000:01:00.0: BAR 2: assigned [mem 0xe0200000-0xe02fffff 64bit pref] [ 0.021032] pci 0000:00:01.0: PCI bridge to [bus 01] [ 0.021038] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xe02fffff] [ 0.021051] pci 0000:02:00.0: BAR 0: assigned [mem 0xe0400000-0xe05fffff 64bit pref] [ 0.021061] pci 0000:02:00.0: BAR 2: assigned [mem 0xe0600000-0xe06fffff 64bit pref] [ 0.021072] pci 0000:00:02.0: PCI bridge to [bus 02] [ 0.021077] pci 0000:00:02.0: bridge window [mem 0xe0400000-0xe06fffff] [ 0.021299] mv_xor f1060800.xor: Marvell shared XOR driver [ 0.082622] mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr ) [ 0.082761] mv_xor f1060900.xor: Marvell shared XOR driver [ 0.142606] mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr ) [ 0.142784] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 0.143058] printk: console [ttyS0] disabled [ 0.163137] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 30, base_baud = 12500000) is a 16550A [ 1.249362] printk: console [ttyS0] enabled [ 1.255328] loop: module loaded [ 1.259019] ahci-mvebu f10a8000.sata: supply ahci not found, using dummy regulator [ 1.266709] ahci-mvebu f10a8000.sata: supply phy not found, using dummy regulator [ 1.274262] ahci-mvebu f10a8000.sata: supply target not found, using dummy regulator [ 1.282095] ahci-mvebu f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode [ 1.291191] ahci-mvebu f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs [ 1.300412] scsi host0: ahci-mvebu [ 1.304083] scsi host1: ahci-mvebu [ 1.307573] ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 50 [ 1.315537] ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 50 [ 1.323954] nand: device found, Manufacturer ID: 0xef, Chip ID: 0xda [ 1.330339] nand: Winbond W29N02GV [ 1.333766] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 1.341551] Bad block table found at page 131008, version 0x01 [ 1.347749] Bad block table found at page 130944, version 0x01 [ 1.353910] 11 fixed-partitions partitions found on MTD device pxa3xx_nand-0 [ 1.360995] Creating 11 MTD partitions on "pxa3xx_nand-0": [ 1.366517] 0x000000000000-0x000000200000 : "u-boot" [ 1.371679] 0x000000200000-0x000000220000 : "u_env" [ 1.376729] 0x000000220000-0x000000260000 : "s_env" [ 1.381756] 0x0000007e0000-0x000000820000 : "devinfo" [ 1.386980] 0x000000820000-0x000000a00000 : "sysdiag" [ 1.392171] 0x000000a00000-0x000005a00000 : "kernel1" [ 1.397478] 0x000001000000-0x000005a00000 : "ubi" [ 1.402430] 0x000005a00000-0x00000aa00000 : "kernel2" [ 1.407739] 0x000006000000-0x00000aa00000 : "rootfs2" [ 1.413038] 0x00000aa00000-0x000010000000 : "syscfg" [ 1.418257] 0x000000260000-0x000000820000 : "unused_area" [ 1.425993] mvneta_bm f10c8000.bm: Buffer Manager for network controller enabled [ 1.434812] mvneta f1070000.ethernet eth0: Using hardware mac address 60:38:e0:cd:1c:90 [ 1.444154] mvneta f1034000.ethernet eth1: Using hardware mac address 60:38:e0:cd:1c:90 [ 1.452304] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.458863] ehci-platform: EHCI generic platform driver [ 1.464186] ehci-orion: EHCI orion driver [ 1.468286] orion-ehci f1058000.usb: EHCI Host Controller [ 1.473724] orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1 [ 1.481370] orion-ehci f1058000.usb: irq 47, io mem 0xf1058000 [ 1.512275] orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00 [ 1.518421] hub 1-0:1.0: USB hub found [ 1.522199] hub 1-0:1.0: 1 port detected [ 1.526568] usbcore: registered new interface driver usb-storage [ 1.532752] i2c_dev: i2c /dev entries driver [ 1.539716] orion_wdt: Initial timeout 171 sec [ 1.544393] sdhci: Secure Digital Host Controller Interface driver [ 1.550601] sdhci: Copyright(c) Pierre Ossman [ 1.555069] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.564508] marvell-cesa f1090000.crypto: CESA device successfully registered [ 1.572065] NET: Registered PF_INET6 protocol family [ 1.577554] Segment Routing with IPv6 [ 1.581254] In-situ OAM (IOAM) with IPv6 [ 1.585237] NET: Registered PF_PACKET protocol family [ 1.585839] mmc0: SDHCI controller on f10d8000.sdhci [f10d8000.sdhci] using ADMA [ 1.597375] 8021q: 802.1Q VLAN Support v1.8 [ 1.602010] Registering SWP/SWPB emulation handler [ 1.609260] usb_phy_generic usb3_1-phy: dummy supplies not allowed for exclusive requests [ 1.617699] xhci-hcd f10f8000.usb3: xHCI Host Controller [ 1.623053] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 2 [ 1.630678] xhci-hcd f10f8000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x0000000000010010 [ 1.640005] xhci-hcd f10f8000.usb3: irq 53, io mem 0xf10f8000 [ 1.645842] xhci-hcd f10f8000.usb3: xHCI Host Controller [ 1.651183] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 3 [ 1.658772] xhci-hcd f10f8000.usb3: Host supports USB 3.0 SuperSpeed [ 1.662507] ata2: SATA link down (SStatus 0 SControl 300) [ 1.665405] hub 2-0:1.0: USB hub found [ 1.670607] ata1: SATA link down (SStatus 0 SControl 300) [ 1.674395] hub 2-0:1.0: 1 port detected [ 1.683841] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM. [ 1.692131] hub 3-0:1.0: USB hub found [ 1.695926] hub 3-0:1.0: 1 port detected [ 1.700222] UBI: auto-attach mtd6 [ 1.703567] ubi0: attaching mtd6 [ 1.725732] mmc0: new high speed SDIO card at address 0001 [ 1.772378] UBI: EOF marker found, PEBs from 203 will be erased [ 1.778428] ubi0: scanning is finished [ 1.798229] ubi0: volume 1 ("rootfs_data") re-sized from 9 to 347 LEBs [ 1.805031] ubi0: attached mtd6 (name "ubi", size 74 MiB) [ 1.810457] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 1.817371] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 1.824198] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 1.831191] ubi0: good PEBs: 592, bad PEBs: 0, corrupted PEBs: 0 [ 1.837229] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128 [ 1.844487] ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 1675813872 [ 1.853664] ubi0: available PEBs: 0, total reserved PEBs: 592, PEBs reserved for bad PEB handling: 40 [ 1.862932] ubi0: background thread "ubi_bgt0d" started, PID 451 [ 1.863401] block ubiblock0_0: created from ubi0:0(rootfs) [ 1.874496] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem [ 1.881664] mvsw61xx 10.mvsw61xx: Found MV88E6352 at f1072004.mdio-mii:10 [ 1.888495] mvsw61xx 10.mvsw61xx: Using direct addressing [ 1.901746] Waiting 1 sec before mounting root device... [ 2.012273] usb 2-1: new high-speed USB device number 2 using xhci-hcd [ 2.964189] VFS: Mounted root (squashfs filesystem) readonly on device 254:0. [ 2.971845] Freeing unused kernel image (initmem) memory: 1024K [ 3.012421] Run /sbin/init as init process [ 3.140185] init: Console is alive [ 3.143703] init: - watchdog - [ 3.676781] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 3.722323] usbcore: registered new interface driver uas [ 3.727808] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 3.740491] init: - preinit - [ 4.096309] mvneta f1070000.ethernet wan: renamed from eth0 [ 4.120953] random: procd: uninitialized urandom read (4 bytes read) [ 4.164483] mvneta f1034000.ethernet lan: renamed from eth1 [ 4.270987] mtdblock: MTD device 'devinfo' is NAND, please consider using UBI block devices instead. [ 4.376449] random: jshn: uninitialized urandom read (4 bytes read) [ 4.414775] random: jshn: uninitialized urandom read (4 bytes read) [ 4.458265] mtdblock: MTD device 'devinfo' is NAND, please consider using UBI block devices instead. [ 4.638042] mvneta f1034000.ethernet lan: configuring for fixed/sgmii link mode [ 4.645890] mvneta f1034000.ethernet lan: Link is Up - 1Gbps/Full - flow control off [ 4.653780] IPv6: ADDRCONF(NETDEV_CHANGE): lan: link becomes ready Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 6.723351] mount_root: loading kmods from internal overlay [ 6.738626] kmodloader: loading kernel modules from //etc/modules-boot.d/* [ 6.746097] kmodloader: done loading kernel modules from //etc/modules-boot.d/* [ 6.819127] UBIFS (ubi0:1): default file-system created [ 6.824746] UBIFS (ubi0:1): Mounting in unauthenticated mode [ 6.830489] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 617 [ 6.863411] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data" [ 6.871280] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 6.881273] UBIFS (ubi0:1): FS size: 42790912 bytes (40 MiB, 337 LEBs), max 347 LEBs, journal size 2158592 bytes (2 MiB, 17 LEBs) [ 6.892983] UBIFS (ubi0:1): reserved for root: 2021120 bytes (1973 KiB) [ 6.899626] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID 82733DDA-E486-42F9-86F9-7DA83DD607FA, small LPT model [ 6.911410] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab [ 6.918469] block: unable to load configuration (fstab: Entry not found) [ 6.925240] block: attempting to load /tmp/ubifs_cfg/etc/config/fstab [ 6.931746] block: unable to load configuration (fstab: Entry not found) [ 6.938510] block: attempting to load /etc/config/fstab [ 6.945753] block: unable to load configuration (fstab: Entry not found) [ 6.952525] block: no usable configuration [ 6.958724] UBIFS (ubi0:1): un-mount UBI device 0 [ 6.963472] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" stops [ 6.971581] UBIFS (ubi0:1): Mounting in unauthenticated mode [ 6.982293] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 620 [ 7.010193] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data" [ 7.018082] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 7.028047] UBIFS (ubi0:1): FS size: 42790912 bytes (40 MiB, 337 LEBs), max 347 LEBs, journal size 2158592 bytes (2 MiB, 17 LEBs) [ 7.039754] UBIFS (ubi0:1): reserved for root: 2021120 bytes (1973 KiB) [ 7.046400] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID 82733DDA-E486-42F9-86F9-7DA83DD607FA, small LPT model [ 7.068237] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab [ 7.075286] block: unable to load configuration (fstab: Entry not found) [ 7.082042] block: attempting to load /tmp/ubifs_cfg/etc/config/fstab [ 7.088555] block: unable to load configuration (fstab: Entry not found) [ 7.095313] block: attempting to load /etc/config/fstab [ 7.100591] block: unable to load configuration (fstab: Entry not found) [ 7.107346] block: no usable configuration [ 7.112199] mount_root: overlay filesystem has not been fully initialized yet [ 7.119512] mount_root: switching to ubifs overlay [ 7.160712] ubi1: attaching mtd9 [ 7.386193] ubi1: scanning is finished [ 7.394230] ubi1: attached mtd9 (name "syscfg", size 86 MiB) [ 7.399921] ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 7.406836] ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 7.413661] ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 7.420653] ubi1: good PEBs: 680, bad PEBs: 8, corrupted PEBs: 0 [ 7.426689] ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128 [ 7.433946] ubi1: max/mean erase counter: 252/185, WL threshold: 4096, image sequence number: 1236736651 [ 7.443471] ubi1: available PEBs: 0, total reserved PEBs: 680, PEBs reserved for bad PEB handling: 32 [ 7.452738] ubi1: background thread "ubi_bgt1d" started, PID 632 UBI device number 1, total 680 LEBs (86343680 bytes, 82.3 MiB), [ 7.463405] UBIFS (ubi1:0): Mounting in unauthenticated mode available 0 LEBs (0 bytes), LEB [ 7.472290] UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 636 size 126976 bytes (124.0 KiB) [ 7.514142] UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "syscfg" [ 7.521575] UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 7.531540] UBIFS (ubi1:0): FS size: 80375808 bytes (76 MiB, 633 LEBs), max 644 LEBs, journal size 4063232 bytes (3 MiB, 32 LEBs) [ 7.543251] UBIFS (ubi1:0): reserved for root: 3796347 bytes (3707 KiB) [ 7.549895] UBIFS (ubi1:0): media format: w4/r0 (latest is w5/r0), UUID CFE39241-7B58-42DE-8C4E-983F183676CA, small LPT model [ 7.563462] urandom-seed: Seed file not found (/etc/urandom.seed) [ 7.611831] mvneta f1034000.ethernet lan: Link is Down [ 7.674334] procd: - early - [ 7.677273] procd: - watchdog - [ 7.821616] random: jshn: uninitialized urandom read (4 bytes read) [ 7.890535] random: jshn: uninitialized urandom read (4 bytes read) [ 7.941825] random: jshn: uninitialized urandom read (4 bytes read) [ 8.209597] procd: - watchdog - [ 8.247078] procd: - ubus - [ 8.303252] procd: - init - Please press Enter to activate this console. [ 8.520071] urngd: v1.0.2 started. [ 8.541914] kmodloader: loading kernel modules from /etc/modules.d/* [ 8.549737] random: crng init done [ 8.553168] random: 35 urandom warning(s) missed due to ratelimiting [ 8.625235] NET: Registered PF_ALG protocol family [ 8.636723] tun: Universal TUN/TAP device driver, 1.6 [ 8.659862] cryptodev: driver 1.12 loaded. [ 8.664399] Loading modules backported from Linux version v6.1-rc8-0-g76dcd734eca2 [ 8.672005] Backport generated by backports.git v5.15.81-1-41-g02e352527db5 [ 8.743792] <> [ 8.751847] pci 0000:00:01.0: enabling device (0140 -> 0142) [ 11.818336] ieee80211 phy0: device node: pcie@1,0 [ 11.851290] ieee80211 phy0: firmware version: 0x903020c [ 11.890398] ieee80211 phy0: 2G disabled, 5G enabled [ 11.895328] ieee80211 phy0: 4 TX antennas, 4 RX antennas [ 11.900858] pci 0000:00:02.0: enabling device (0140 -> 0142) [ 13.248324] ieee80211 phy1: device node: pcie@2,0 [ 13.281293] ieee80211 phy1: firmware version: 0x903020c [ 13.313353] ieee80211 phy1: 2G enabled, 5G disabled [ 13.318264] ieee80211 phy1: 4 TX antennas, 4 RX antennas [ 13.364722] videodev: Linux video capture interface: v2.00 [ 13.371935] hid: raw HID events driver (C) Jiri Kosina [ 13.381880] ntfs3: Max link count 4000 [ 13.385690] ntfs3: Enabled Linux POSIX ACLs support [ 13.394746] fuse: init (API version 7.34) [ 13.406920] Bluetooth: Core ver 2.22 [ 13.410573] NET: Registered PF_BLUETOOTH protocol family [ 13.415938] Bluetooth: HCI device and connection manager initialized [ 13.422340] Bluetooth: HCI socket layer initialized [ 13.427243] Bluetooth: L2CAP socket layer initialized [ 13.432333] Bluetooth: SCO socket layer initialized [ 13.437974] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 13.443351] Bluetooth: BNEP filters: protocol multicast [ 13.448608] Bluetooth: BNEP socket layer initialized [ 13.463697] Bluetooth: vendor=0x2df, device=0x9136, class=255, fn=2 [ 14.172757] Bluetooth: FW download over, size 616840 bytes [ 14.812303] btmrvl_sdio mmc0:0001:2: sdio device tree data not available [ 14.820523] usbcore: registered new interface driver btusb [ 14.826583] usbcore: registered new interface driver cdc_acm [ 14.832290] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 14.845522] Bluetooth: HCI UART driver ver 2.3 [ 14.849995] Bluetooth: HCI UART protocol H4 registered [ 14.855165] Bluetooth: HCI UART protocol BCSP registered [ 14.861085] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 14.867048] Bluetooth: HIDP socket layer initialized [ 14.873216] usbcore: registered new interface driver ipheth [ 14.885239] mwifiex_sdio mmc0:0001:1: WLAN FW already running! Skip FW dnld [ 14.892244] mwifiex_sdio mmc0:0001:1: WLAN FW is active [ 14.918438] Bluetooth: RFCOMM TTY layer initialized [ 14.923403] Bluetooth: RFCOMM socket layer initialized [ 14.928579] Bluetooth: RFCOMM ver 1.11 [ 14.933476] usbcore: registered new interface driver ums-alauda [ 14.940365] usbcore: registered new interface driver ums-cypress [ 14.947158] usbcore: registered new interface driver ums-datafab [ 14.953652] usbcore: registered new interface driver ums-freecom [ 14.960037] usbcore: registered new interface driver ums-isd200 [ 14.966643] usbcore: registered new interface driver ums-jumpshot [ 14.973323] usbcore: registered new interface driver ums-karma [ 14.979564] usbcore: registered new interface driver ums-sddr09 [ 14.986714] usbcore: registered new interface driver ums-sddr55 [ 14.993546] usbcore: registered new interface driver ums-usbat [ 15.006042] usbcore: registered new interface driver usbserial_generic [ 15.012672] usbserial: USB Serial support registered for generic [ 15.035000] mwifiex_sdio mmc0:0001:1: info: MWIFIEX VERSION: mwifiex 1.0 (15.68.7.p189) [ 15.043160] mwifiex_sdio mmc0:0001:1: driver_version = mwifiex 1.0 (15.68.7.p189) [ 15.101724] xt_time: kernel timezone is -0000 [ 15.108365] usbcore: registered new interface driver ftdi_sio [ 15.114251] usbserial: USB Serial support registered for FTDI USB Serial Device [ 15.127859] usbcore: registered new interface driver uvcvideo [ 15.133971] kmodloader: done loading kernel modules from /etc/modules.d/* [ 15.286197] mtdblock: MTD device 'devinfo' is NAND, please consider using UBI block devices instead. [ 15.505354] mtdblock: MTD device 'devinfo' is NAND, please consider using UBI block devices instead. [ 18.945547] mvneta f1034000.ethernet lan: configuring for fixed/sgmii link mode [ 18.953091] mvneta f1034000.ethernet lan: Link is Up - 1Gbps/Full - flow control off [ 18.962054] br-lan: port 1(lan) entered blocking state [ 18.967249] br-lan: port 1(lan) entered disabled state [ 18.972614] device lan entered promiscuous mode [ 18.982596] br-lan: port 1(lan) entered blocking state [ 18.987768] br-lan: port 1(lan) entered listening state [ 19.081240] mvneta f1070000.ethernet wan: configuring for fixed/rgmii-id link mode [ 19.090441] mvneta f1070000.ethernet wan: Link is Up - 1Gbps/Full - flow control off [ 19.111277] br-tu: port 1(wan) entered blocking state [ 19.116398] br-tu: port 1(wan) entered disabled state [ 19.121600] device wan entered promiscuous mode [ 19.143092] br-tu: port 1(wan) entered blocking state [ 19.148194] br-tu: port 1(wan) entered forwarding state [ 20.482503] ipheth 2-1:4.2: ipheth_enable_ncm: usb_control_msg: 0 [ 20.489024] ipheth 2-1:4.2: Apple iPhone USB Ethernet device attached [ 20.974562] ieee80211 phy1: change: 0xffffffff [ 21.085516] br-lan: port 2(i2) entered blocking state [ 21.090656] br-lan: port 2(i2) entered disabled state [ 21.095961] device i2 entered promiscuous mode [ 21.192672] ieee80211 phy1: change: 0x100 [ 21.205745] ieee80211 phy1: change: 0x42 [ 21.358422] IPv6: ADDRCONF(NETDEV_CHANGE): i2: link becomes ready [ 21.364641] br-lan: port 2(i2) entered blocking state [ 21.369725] br-lan: port 2(i2) entered listening state [ 21.674300] ieee80211 phy0: change: 0xffffffff [ 21.781832] br-lan: port 3(ivan) entered blocking state [ 21.787101] br-lan: port 3(ivan) entered disabled state [ 21.792458] device ivan entered promiscuous mode [ 21.797141] br-lan: port 3(ivan) entered blocking state [ 21.802400] br-lan: port 3(ivan) entered listening state [ 21.862511] ieee80211 phy0: change: 0x100 [ 21.875559] ieee80211 phy0: change: 0x42 [ 22.045308] IPv6: ADDRCONF(NETDEV_CHANGE): ivan: link becomes ready [ 22.092437] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 22.342403] ieee80211 phy1: staid 1 deleted [ 22.812786] br-tu: port 2(tap_tu) entered blocking state [ 22.818141] br-tu: port 2(tap_tu) entered disabled state [ 22.823616] device tap_tu entered promiscuous mode [ 22.828501] br-tu: port 2(tap_tu) entered blocking state [ 22.833860] br-tu: port 2(tap_tu) entered forwarding state [ 27.346187] br-lan: port 1(lan) entered learning state [ 29.887935] br-lan: port 3(ivan) entered learning state [ 29.893211] br-lan: port 2(i2) entered learning state [ 35.609479] br-lan: port 1(lan) entered forwarding state [ 35.614829] br-lan: topology change detected, propagating [ 35.620319] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready [ 38.163398] br-lan: port 2(i2) entered forwarding state [ 38.168658] br-lan: topology change detected, propagating [ 38.174105] br-lan: port 3(ivan) entered forwarding state [ 38.179531] br-lan: topology change detected, propagating [ 48.086061] ieee80211 phy1: staid 1 deleted BusyBox v1.36.0 (2023-02-07 12:19:14 UTC) built-in shell (ash) _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ----------------------------------------------------- OpenWrt SNAPSHOT, r22028-af78f7bbd4 -----------------------------------------------------